Stage 7: Installation practice · topic 28 of 53

DC wiring, connectors and labelling

DC wiring is where workmanship faults can become failed connections and fires. You will be able to check a string installation for matched connectors, right-tool crimps, water protection, polarity and labels, and say who may do each step.

  • Core
  • Intermediate
  • about 14 hours

Part of the Solar PV technician roadmap: from first safety to mid level

Written by the GreenHired editorial teamSources last checked 20 November 2026How we research roadmaps

Before anyone climbs the roof, DC wiring comes down to decisions: who is authorised to make each connection, which tool and connector pair the maker specifies, where every connector will sit, and what stays open until testing is done. The faults can stay hidden on the day. MIS 3002 notes that wrong crimping and assembly tools are a significant factor in failed connections and even fires, and a poor joint can pass a quick look.

Marking up the string routes on paper

Here is a desk check of a drawing for a two-string domestic array with the inverter in the loft. It is not a guide to doing the work.

For each string, trace the cable from the first module to the inverter and mark:

  1. Every connector position. If one lands at the lowest point of a run, in a valley or beside a gutter, ask the designer or supervisor to move or raise it. MIS 3002 lists raising the connector, moving it away from where water could collect, and forming a drip loop.
  2. Every sharp edge or hot roof surface the cable would touch. Each needs a support or a different route.
  3. Every enclosure entry: from below, one cable per gland.
  4. Every label position, readable from where a person would stand to work.

The result is a marked-up drawing and a photo list with one photo per mark, taken before anything is covered. The decision at each mark belongs to the supervisor or electrician. Cable ratings and connectors themselves are chosen at design, covered in cables, protection and earthing.

Who may make the connections

This depends on the country. The Energy Safe Victoria and WorkSafe Victoria guideline (December 2018) treats installing PV as electrical installation work for licensed workers. Someone without a licence may only locate, mount or fix in place individual items of extra-low-voltage equipment, and may not make or terminate their connections. A German industry agreement from BG BAU describes an 8-unit training module covering DC cabling and connectors made while cables are de-energised, under an electrician’s supervision. Check the current rules with your own regulator.

Leaving the strings ready for the testers

Whoever tests next, as in inspection and tests before switch-on, reads polarity and insulation from the string ends left for them. Capped, labelled and photographed ends mean nobody has to guess which cable is which. Strings stay open until an authorised person says otherwise, because DC cables can stay live with the power off: see electrical safety for solar work.

This page teaches standards and practice. It does not authorise live DC work, and no task here touches a live system.

What you will learn

  • Why MIS 3002 requires the connector maker's tools and procedure, and what a wrong crimp can lead to.
  • How string cables are routed and supported so connectors stay out of standing water, with drip loops and UV-rated supports.
  • Why connectors must be a matched pair, and why polarity is checked before anything is closed up.
  • How cables enter an enclosure (from below, one per gland) without losing its ingress rating.
  • How labels, isolators and strings left open until tested support safe working later.
  • Which DC work needs a licensed electrician, and what an instructed assistant may do under supervision in your region.

The parts of this topic

Right-tool crimping and connector assemblyabout 3 hours

MIS 3002 says DC plug and socket connectors must be assembled with the correct tools and procedures, because wrong tools are a significant contributing factor in failures and fires.

MIS 3002 issue 6.0 clause 5.6.4 requires DC connectors to be assembled with the correct tools and procedures to minimise the risk of failure. Its note names incorrect crimping and assembly tools as a significant contributing factor in failed connections and even fires. Use the connector maker's crimp tool and strip length for that cable size, and pull-test as the instructions say. Example: a general-purpose crimper can make a joint that looks fine and heats up later.

Keeping water out: drip loops and cable entryabout 2 hours

Keep DC connectors out of standing water, use drip loops, enter enclosures from below with one cable per gland and keep the IP rating.

A neat run can still leave every connector at its lowest point, as when a connector is left lying on a flat-roof membrane through winter. MIS 3002 says DC connectors should be protected from water ingress for the system's life. Its note suggests raising a connector out of the water, placing it away from where water could collect, and forming a drip loop. For external enclosures it calls for cable entry at the bottom, a drip loop and a single cable per gland to keep the IP rating.

Matched connectors and polarityabout 3 hours

Join only connectors designed to mate, and make sure positive meets positive along the string. A failed or wrong connector can open or short a circuit.

PVPMC notes that a blown fuse, broken wire or failed connector can create an open circuit. Join only connectors made to mate: match brand and type unless the maker declares them compatible, because two plugs that click together may still be incompatible. Set each string's polarity from the module labels and check it before anything is closed up. IEC 62548-1 covers DC array wiring, protection and switching. The Victorian guideline warns that incorrect connections, such as panel to panel connectors, may cause serious shock or injury.

Cable support, UV and routingabout 2 hours

Support string cables so they cannot chafe, sag into water or catch the wind, using UV-resistant ties and clips, and keep the plan's cable route.

The UPNEDA 3 kW bill of materials lists UV-protected nylon and stainless-steel cable ties, flexible conduit or cable tray, MC4 connectors and ring lugs: the kind of items a tidy installation needs. Support cables at the intervals the manufacturer and design give, keep them off sharp edges and away from roof surfaces that heat up, and separate positive and negative runs if the design requires it. Slack that rubs the roof, for instance, is what MIS 3002's maintenance check for "cables adequately supported and free of damage" later finds.

Isolators and labellingabout 2 hours

DC isolators and labels tell the next person where the system is live and how to shut it down. Fit them as designed, and label as the code requires.

Labels fail in ordinary ways: too small to read, faded by sunlight, or hidden by scaffolding. Place them where they can be read from the working position, and match the design. IAEI's 2023 NEC summary lists new 690.7(D) marking for DC PV circuits and says rapid shutdown marking moved to 690.12(D); a second IAEI article covers how rapid shutdown itself changed. In the UK, the maintenance schedule in MIS 3002 includes checking that labelling and signage are present and that an emergency shutdown procedure is visible.

Strings left open until testedabout 2 hours

Leave strings unconnected to the inverter and open until tests are done. Strings and cables can carry voltage in daylight, so treat them as live.

HSE's HSG85 sets out safe working practices for people working on or near electrical equipment, and the Victorian guideline says solar DC cables can still be live with the power off. Keep string ends capped and separated, and connect them to the inverter only when the tests are complete and an authorised person says so. Example: uncapped string ends of opposite polarity lying side by side. Closing the isolator "to see if it works" skips the tests that are meant to answer that.

Practice task

Take a connector maker's free assembly instructions and the MIS 3002 clauses on DC connectors, and write a one-page checklist for a DC string installation: tools, assembly steps, support and drip-loop rules, polarity and labelling checks, what must stay open, and who is authorised for each step in your region. Add a column for the photo you would take at each step. Paper only: touch no live system.

Skills you build

Connector assembly standardsCable routing and supportPolarity and label checksReading installation instructions

Resources for this topic

Every source here is free. Each link opens the provider's own site in a new tab.

Back to the whole roadmap

Live jobs

Latest Renewable Energy jobs

No title matches the role right now, so these are the latest jobs in the same category.

All Renewable Energy jobs

No live jobs to show right now. Check back soon, or browse every green job.

Spot a problem with this topic?

Tell us what is wrong, missing or unclear here. Your note is attached to this topic.

Notes are sent from this page with JavaScript on. Without it, write to us on the contact page.