Arc flash, DC arcs and fire risk
Arc and fire hazards in solar work, from a poorly made connector to a roof fire or a failing battery. You will learn what starts them, which controls reduce them and where your own limits are.
- Core
- Intermediate
- about 10 hours
Written by the GreenHired editorial teamSources last checked 20 November 2026How we research roadmaps
Fire is a chain: something ignites, something carries the flames, and someone has to deal with the result. Your influence is greatest at the first link, in small places such as a connector, a cable run or a setting. So find the ignition points first, tie one control to each, and only then ask what a firefighter or the customer would need to see.
A badly crimped connector, link by link
A flat-roof array has connectors crimped with the wrong tool. This is how a risk-note entry is built, the method behind the practice task, and it is not a repair guide.
A poor contact heats under load. If it arcs, a DC arc has no zero crossing to die out on, so it can keep burning until something gives way. The controls that interrupt that chain are the right tool and procedure (MIS 3002 clause 5.6.4 in Issue 6.0), connectors the makers approve for each other, connectors raised out of puddles with a drip loop (5.6.3), and the inverter’s arc-fault detection switched on where it has one (5.6.7). That last control is a safety net, not a reason to accept a poor crimp, and only some inverters have it. The evidence is the commissioning record showing the setting is on, and photos of the connector heights.
Now a later visit finds a warm or discoloured connector. Treat it as live: in daylight the modules and cable on the array side stay energised even with the inverter off, as electrical safety for DC and AC solar work explains. Keep clear, tell your supervisor or the responsible electrician, and record what you saw; that record is a lead for DC fault finding. Repair is for someone authorised; nothing on this page authorises you to open live DC wiring.
What a firefighter needs from your design
Ask two questions at design stage. Does the roof keep its fire performance? MIS 3002 clause 5.8.1 asks the contractor to be able to show it does. And can someone who has never seen the site shut it down? Labels at the consumer unit and the isolators, a written shutdown sequence in the handover pack, and rapid shutdown where your region’s code requires it all help answer that. For batteries the same questions move earlier, to siting: see storage safety, siting and codes.
NFPA 70E in the job postings
If US commissioning or O&M work is your aim, NFPA 70E is worth knowing early: 3 of the 17 job postings in our sample (UK, US, Germany, India and Australia; how we research roadmaps) asked for it, all in the US, and 3 US commissioning or O&M postings named lockout/tagout or arc flash.
What you will learn
- Why a DC arc is harder to stop than an AC arc, and what usually starts one
- What arc flash is and what NFPA 70E is for
- How wrong tools and mismatched connectors lead to heating, arcing and fires
- What arc-fault detection and rapid shutdown do, and what UL 3741 is
- How gaps under panels speed fire spread over a roof, and why roof coverings matter
- Why battery thermal runaway, labels and shutdown steps matter to firefighters
The parts of this topic
DC arc behaviourabout 1 hour
A DC arc does not self-extinguish, can burn for a long time and reaches extreme temperatures, so prevention matters most.
In AC the current crosses zero many times a second, which helps an arc die out. In DC it never does, so an arc can persist until something burns through or the circuit opens: never assume it will stop by itself. Prevention comes from sound connections and inspection. Example: a poorly made connector that heats and arcs over months, long after the installer has gone. The BRE report on fires and solar PV systems has a chapter on ignition mechanisms and electrical arcing.
- Fire and solar PV systems: investigations and evidence (BRE, issue 2.9) BRE for UK Government · Guide Published 2018; useful for how fires started, but check newer guidance.
Arc-flash PPE and NFPA 70Eabout 1 hour
NFPA 70E is the US standard on electrical safety at work; arc-rated PPE is the last line of defence, after isolation.
NFPA 70E, Standard for Electrical Safety in the Workplace, is the US reference for electrical safe work practices, including arc-flash risk assessment and arc-rated clothing. OSHA's solar guidance lists arc flash (burn and blast) among the main hazards of solar work and covers PPE. PPE is the last control, not the first: isolation and de-energised work come before it. Equipment may carry an employer's arc-flash label stating the PPE category. NFPA sells the full text, so check nfpa.org for the access it offers to the current edition.
- Solar energy: personal protective equipment OSHA (United States) · Guide
Connector failures and how to prevent themabout 1 hour
Wrong crimp tools, mismatched brands, water ingress and strain all cause connector heating and arcing.
MIS 3002 asks for DC connectors to be assembled with the correct tools and procedures, and protected from water for the life of the system, for example by raising them out of puddles on a flat roof or adding a drip loop. Its note says wrong crimping tools have been a significant contributing factor in connection failures and even fires. Only mate connectors the makers approve for each other: fitting together is not the same as compatible. The Sandia modelling guide lists connector failure among common DC component faults.
- MIS 3002:2025 Issue 2.0 (redeveloped MCS scheme) MCS · Standard Clauses 3.6.3 to 3.6.5 in this issue (5.6.3 to 5.6.5 in Issue 6.0).
- PVPMC: DC component health Sandia National Laboratories · Guide
Arc-fault detection in invertersabout 1 hour
Where an inverter has an arc-fault detection function, the UK standard says it shall be enabled.
Many modern inverters can detect a series arc in the DC wiring and switch off. MIS 3002 clause 5.6.7 (Issue 6.0) says that where an inverter has an arc-fault detection function, it shall be enabled. Example: at commissioning the technician checks that the function is switched on in the inverter settings and records it. If it trips again and again, do not switch it off to stop the nuisance. Report it, because the cause may be a real connector fault.
- MIS 3002 Issue 6.0: the Solar PV Standard (Installation) MCS · Standard Free to read. Dated 18 March 2026; mandatory for contractors certified under it from 18 June 2026. The library also lists a redeveloped MIS 3002:2025 Issue 2.0, so check which one your employer is certified to.
Rapid shutdown and UL 3741about 1 hour
US rules require rapid shutdown of certain PV conductors; UL 3741 covers PV hazard control systems.
IAEI Magazine describes rapid shutdown as a workplace-safety measure for firefighters working on roofs with PV arrays. Its requirements sit in section 690.12 of the National Electrical Code, and the article covers how UL 3741 relates to it. Rapid shutdown limits voltage within set boundaries; it is not proof that an array is dead. Requirements and exemptions differ between NEC editions and between states and local authorities. In one design, module-level devices shut down when the control signal is lost. Quote the rules of the edition your local authority has adopted, not another one.
- NEC rapid shutdown requirements and UL 3741 IAEI Magazine · Guide
- 2023 National Electrical Code and photovoltaic power systems IAEI Magazine · Guide Trade-magazine summary of the 2023 NEC changes; adoption varies by state.
Roof gaps and fire spreadabout 1 hour
The gap under panels can trap heat and speed flame spread, so roof coverings and layouts matter for fire safety.
UK government research found that gaps under panels can trap heat and help flames spread, and recommends non-combustible roof coverings. MIS 3002 clause 5.8.1 says the contractor must be able to show that fitting the modules left the roof's fire performance unchanged: by mounting above an existing non-combustible covering, or by using an in-roof kit with the right fire rating. Appendix C gives a worked fire-rating example. Fire rules apply to ordinary houses, not only to big buildings.
- Thermal exposure to roofs from fires involving PV panels OFR Consultants for the Building Safety Regulator · Guide Review dated 7 January 2026; long and technical, so read the abstract and recommendations first.
- Fire safety: Approved Document B GOV.UK · Law or regulation
Battery thermal runawayabout 1 hour
A failing battery cell can overheat and spread to others; siting and standards aim to limit the damage.
Thermal runaway is when a battery cell overheats, damages neighbouring cells and keeps heating, and it can be very hard to stop once started. The Victorian guideline lists the hazards: overheating, over- or under-charging, mechanical damage and chemicals. A home battery is not an ordinary appliance: its siting, separation and instructions all matter, and placing it away from escape routes, as the manufacturer's and code instructions say, is one example. NFPA 855 covers installing stationary energy storage systems, including siting and separation.
- Working safely when installing photovoltaic (PV) systems (Victoria, Australia, 2018) Energy Safe Victoria and WorkSafe Victoria · Guide A 2018 state guideline: rules differ by state, so use it for the hazards, not for your local law.
Extinguishers, labels and shutdown stepsabout 1 hour
Labels and a clear shutdown procedure help the customer, you and firefighters, but an extinguisher is not a licence to fight a fire.
Good installations carry labels showing where the isolators are and what the shutdown steps are, and the customer receives written shutdown instructions at handover. At the consumer unit, a label can point to the PV isolators. HSE guidance on controlling fire and explosion risks covers general fire precautions. Modules stay live in light, so fighting a fire on a live array is dangerous: get people out and call the fire service. An extinguisher on the van does not change that.
- Controlling fire and explosion risks in the workplace (INDG370) HSE (Great Britain) · Guide
Practice task
Write a two-page fire-and-arc risk note for a fictional domestic roof system with a battery. Cover the three most likely ignition points (for example a poor connector, a damaged cable and a battery fault), the control for each (correct tools, inspection, arc-fault function enabled, siting), the labels and shutdown steps a firefighter would need, and the limits of the roof covering. Check each claim against one source linked here and say which.
Skills you build
DC arc awarenessArc-flash PPE awarenessConnector qualityRapid shutdown awarenessRoof fire spreadBattery fire awareness
Resources for this topic
Every source here is free. Each link opens the provider's own site in a new tab.
- Green job hazards: solar energy OSHA (United States) · Guide
- Electrical hazards (OSHA safety and health topic) OSHA (United States) · Guide
- Fire incidents involving solar panels GOV.UK · Guide
Latest Renewable Energy jobs
No title matches the role right now, so these are the latest jobs in the same category.
No live jobs to show right now. Check back soon, or browse every green job.
Spot a problem with this topic?
Tell us what is wrong, missing or unclear here. Your note is attached to this topic.
Notes are sent from this page with JavaScript on. Without it, write to us on the contact page.