Stage 10: Storage, EV charging and smart energy · topic 40 of 53

Battery storage fundamentals

How home and commercial batteries work: energy against power, usable capacity, chemistries, coupling, backup and sizing. You will be able to compare two products and size a battery from real household use.

  • Core
  • Intermediate
  • about 12 hours

Part of the Solar PV technician roadmap: from first safety to mid level

Written by the GreenHired editorial teamSources last checked 20 November 2026How we research roadmaps

The vocabulary builds up in a fixed order. Energy (kWh) against power (kW) comes first, then nominal against usable capacity, then how the battery joins the system (DC- or AC-coupled), and only then what the customer wants it for. Sizing comes last because it depends on everything before it. A battery chosen without a goal is either too big to pay back or too small to do the job.

Employers ask for storage skills: of the 17 postings we sampled (UK, US, Germany, India and Australia; how we research roadmaps), 7 asked for a battery or storage award or skill, including 3 of the 4 UK postings.

Sizing for the evening bill, then for an outage

A household uses 8 kWh between 17:00 and 23:00 and wants less grid import in the evening. Its evening peak is 6 kW, when the oven, kettle and a heat pump overlap. The candidate battery is 10 kWh nominal with a 5 kW continuous limit, and 90% of it usable (an assumed figure: read the real one on the datasheet). Every figure here is invented, and none is a recommendation.

  • Bill saving only: usable capacity is 10 x 0.9 = 9 kWh, which covers the 8 kWh evening with 1 kWh to spare. The 6 kW peak is 1 kW over the 5 kW limit, so that 1 kW comes from the grid for those minutes. For bill-saving that is acceptable.
  • Bill saving plus backup: the customer also wants the fridge, lights and router (1.5 kW, assumed) kept running in an outage: 9 / 1.5 = 6 hours from a full battery, ignoring losses. And if 30% of the usable energy is held back as a backup reserve, the evening gets only 9 x 0.7 = 6.3 kWh, which is 1.7 kWh short of the 8 kWh need.

So one battery cannot serve both goals fully. The fix is a conversation, not a bigger box: pick the main goal, set the reserve to match, and write down what each goal gets.

Hands-on battery work needs authorisation

A battery adds a hazard that does not switch off when the sun goes down. Do not open, move or connect a battery unless you are trained, instructed and permitted to, and work only within your local licensing rules. Storage safety, siting and codes covers the hazards, and installing and commissioning storage shows who does which step. The hybrid inverter side is in inverters, optimisers and microinverters.

What you will learn

  • What kWh (energy) and kW (power) mean for a battery, and the difference between nominal and usable capacity.
  • How lithium-ion chemistries differ in cycle life, heat tolerance and cost of failure.
  • What a battery management system does and why it cannot protect against everything.
  • How AC-coupled and DC-coupled systems and hybrid inverters are arranged.
  • How backup and islanding differ from ordinary self-consumption, and how to size a battery from a household's real use.

The parts of this topic

Lithium-ion chemistriesabout 2 hours

LFP, NMC and others differ in cycle life, heat tolerance and how badly a failure can behave, which affects siting and cost.

Battery University's chemistry article compares types by cycle life and thermal-runaway onset: LFP is described as very safe even when fully charged, with a runaway onset around 270 C and 2,000 or more cycles; NMC starts around 210 C and lists 1,000 to 2,000 cycles. Some home batteries use LFP for those reasons, but read the datasheet for the actual chemistry. Example: two batteries with the same kWh and price can differ in warranty throughput, temperature range and installation requirements, so compare those before you choose.

kWh, kW, depth of discharge and cyclesabout 2 hours

Energy (kWh), power (kW), usable capacity and how deep each cycle goes decide how long a battery lasts and what it can run.

kWh is how much energy it holds; kW is how fast it can deliver or take it. A 10 kWh battery with a 5 kW limit cannot run an 8 kW load. Usable capacity is lower than nominal because a reserve is held back. Shallower discharges extend life: Battery University's table gives about 300 cycles at full depth versus about 6,000 at 10% depth for NMC, and notes heat accelerates ageing. Compare products by usable kWh, power and warranty throughput, not by headline kWh.

Battery management systemabout 1 hour

The BMS watches cell voltage, current and temperature and disconnects the pack when limits are exceeded, but it has limits too.

Large lithium packs need protection: limit charge voltage, cut off on high temperature, stop discharge at low voltage. In a heatwave, for instance, a BMS may trip the pack on over-temperature. Battery University explains that a protection circuit guards against outside abuse such as shorts or bad chargers, not against internal cell defects, and that large multi-cell packs can enter thermal runaway before the remaining safety devices act. Do not assume the BMS makes a battery safe in any position or after damage.

Round-trip efficiency and standby lossesabout 2 hours

Not all energy put in comes back out; conversion and standby losses make real systems worse than the datasheet figure.

Round-trip efficiency is the share of energy that comes out for every unit put in; standby losses are the energy the system uses just by being on. Quoting the datasheet efficiency for a battery that spends most of its life in low-power standby overstates what the customer gets. The IEA PVPS report on battery systems in solar plants proposes six core indicators (capacity, power tolerance, internal resistance, round-trip efficiency, response time, standby losses) and found large gaps between nominal and real-world performance in field data.

AC-coupled and DC-coupled systemsabout 1 hour

A battery can join the system on the AC side or the DC side; the choice affects efficiency, retrofit options and wiring.

In a DC-coupled system the battery shares a DC bus with the solar array and one hybrid inverter does the conversion. In an AC-coupled system the battery has its own inverter and connects on the AC side, which makes retrofitting to an existing solar system easier. Manufacturer manuals show the allowed arrangements; Enphase's documentation centre, for example, groups its battery, gateway and microinverter documents so you can check what pairs with what. Combine only equipment the maker approves together.

Hybrid invertersabout 1 hour

A hybrid inverter handles solar, battery and grid in one unit, so it has more modes, more settings and more ways to be set up wrongly.

A hybrid inverter combines the solar inverter and the battery charger, and often provides a backup output. It chooses between charging, discharging, exporting and importing by rules the installer sets, such as a minimum reserve level for backup. Settings copied from another site rarely fit, because the grid profile, export limit, tariff and backup wiring differ by site and country. Maker support sites list firmware, settings and troubleshooting.

Backup supply and islandingabout 1 hour

Backup means the house keeps running on the battery when the grid fails, which needs dedicated circuits and safe separation from the grid.

Ordinary self-consumption systems shut down when the grid fails, to protect line workers. Backup systems must disconnect from the grid, then supply selected circuits. The 2023 NEC added a part on interconnected systems operating in island mode in Article 705, according to the IAEI summary. Wiring a backup board, choosing which circuits to back up and testing the changeover are skilled electrical tasks done by authorised people. Example: a small battery cannot deliver whole-house backup, so agree the backed-up circuits with the customer before you promise anything.

Sizing a batteryabout 2 hours

Size from the household's real use pattern and the goal (self-consumption, backup or tariff), not from the largest unit available.

Start with half-hourly or daily use, the evening share and what the customer wants: cut bills, survive outages or follow a tariff. Then match usable kWh and kW to that. A home using 8 kWh in the evening, for instance, needs about that much usable capacity, not a nominal figure. PVGIS includes grid-connected, off-grid and tracking tools you can use to explore solar yield for a site. A battery bigger than the evening need may sit part-empty and take longer to pay back.

Practice task

Paper-size a battery for one household using your own bill or a public sample profile: daily use, share used in the evening, usable kWh needed and power needed in kW. Compare two products' public datasheets for usable capacity, power rating and round-trip efficiency, and write a one-page recommendation that states every assumption. This is a desk task; it involves no installation or equipment.

Skills you build

Battery terminologyChemistry comparisonSystem couplingStorage sizingDatasheet comparison

Resources for this topic

Every source here is free. Each link opens the provider's own site in a new tab.

Back to the whole roadmap

Live jobs

Latest Renewable Energy jobs

No title matches the role right now, so these are the latest jobs in the same category.

All Renewable Energy jobs

No live jobs to show right now. Check back soon, or browse every green job.

Spot a problem with this topic?

Tell us what is wrong, missing or unclear here. Your note is attached to this topic.

Notes are sent from this page with JavaScript on. Without it, write to us on the contact page.