Safe systems of work, permits and isolation
Permits to work, isolation and contractor controls turn high-risk jobs into checked steps. You will learn how each works, how to audit a permit at the job and who may stop work, so you can review the system, not do the job.
- Core
- Intermediate
- about 12 hours
Written by the GreenHired editorial teamSources last checked 20 November 2026How we research roadmaps
Confined space entry, hot work, isolation and electrical work are done by trained, competent people under the law and procedures that apply where you work, never by a learner working from a roadmap. Your skill is to ask of any permit: does it describe the real job, did the authoriser visit, is isolation proved, who else is working nearby, and who can stop it?
Auditing a live hot-work permit at the job
A maintenance shutdown has a hot-work permit for a repair in a plant room. The scenario is invented to show how an audit decision is made. It is not guidance for doing hot work.
- Pick a live permit from the permit board, not a closed one from the filing cabinet.
- Read what it promises. This one lists fire precautions, including a person watching the work, and records the area as cleared of combustibles at 07:00.
- Go to the job. At 11:00 the person watching has gone on a break, and another crew has stacked packaging nearby for a different task.
- Decide. The permit no longer matches the work, so ask for the work to stop, record what you saw and who you told, and leave the question of fault for later.
- Fix the system. Re-issue the permit only after the area is checked again, then ask why a second crew could stack packaging without the permit holder knowing. One possible cause is that nobody had authority over the whole area.
- Check closure. Compare the cancelled permits from the same shutdown.
The paper looked fine and the work location did not, which is why the audit starts at the job.
Overlaps and contractors are where the gaps open
The clash above came from two jobs sharing a place, the simultaneous operations problem. HSE calls safe working with contractors a challenge. Outside crews may be new to the site, and your duties do not move to them with the contract. Check competence before you select them and induct every worker. Legal registers, permits and inspections shows where contractor duties sit in your files, and risk assessment step by step is the method a permit’s hazards should come from.
Permit paperwork as portfolio evidence
Among the 18 job postings we sampled (UK, Ireland, EU, US, India, Middle East and Asia; how we research roadmaps), 7 named permit to work and 7 named contractor management. A clear permit form and audit checklist from the practice task make good portfolio material. For the plant hazards that permits cover, see electrical safety, lifting, pressure systems and site transport.
What you will learn
- What a permit to work is and which jobs need one.
- The differences between hot work, confined space, height and electrical permits.
- How lockout/tagout and process isolation prevent unexpected energy release.
- How to select and induct contractors and coordinate jobs that overlap in one area.
- How to audit permits at the job, not just on paper.
- Who may stop work and what protection they have.
The parts of this topic
What a permit to work isabout 1 hour
A permit to work is a written system for dangerous jobs: what work, where, the hazards, the precautions, who authorises it, who does it and how it is closed.
A permit that is a form signed in the office, not a conversation at the job, is the failure to avoid. The Irish HSA describes a permit-to-work as a written system of procedures to safeguard workers doing repair, maintenance or cleaning in potentially dangerous areas or with dangerous operations, involving isolation or monitoring of the atmosphere. It says employers should state in the safety statement which work needs one. A pump repair, for instance, needs isolation, draining, atmosphere checks and sign-off before and after.
- Safety statement and risk assessment Health and Safety Authority (Ireland) · Guide Defines a permit-to-work system.
- Permit to work systems (COMAH technical measures) HSE (UK) · Guide Human factors, management and contents of work permit systems on chemical plant.
Hot work, confined space, height and electrical permitsabout 1 hour
Each high-risk job type needs its own checks. One generic form for everything hides the checks that matter.
Each type of high-risk job needs its own checks: an entry permit should record atmosphere tests and a hot-work permit the fire precautions, and one generic form for all hazards hides the checks that matter. OSHA's process safety guidance says a permit for hot work on or near a covered process must document that fire prevention and protection requirements are in place, state the authorised dates and identify the object, and be kept on file until the work is done. HSE's Confined Spaces ACOP explains the definition of a confined space and helps you assess the risk. HSE's HSG85 covers safe working practices for electrical work.
- Safe work in confined spaces (L101) HSE (UK) · Guide Publication combines the Confined Spaces Regulations 1997 with an Approved Code of Practice and guidance; HSE says the Code has special legal status and that other guidance is not compulsory.
- Electricity at work: safe working practices (HSG85) HSE (UK) · Guide
Lockout and tagoutabout 1 hour
Lockout/tagout isolates machines from energy sources and locks them off during servicing. The US standard requires procedures, training and periodic inspection.
OSHA's standard 29 CFR 1910.147 requires an energy control program of procedures, employee training and periodic inspections, so that machines are isolated from the energy source and rendered inoperative before servicing. Where a device can be locked out, lockout is used; tags without locks, or locks removed by someone else, defeat the system. The standard covers group lockout and shift changes, and requires a periodic inspection of the procedure at least annually by an authorised employee other than those using it. Example: each crew member applies a personal lock before work starts.
- 29 CFR 1910.147: the control of hazardous energy OSHA (US) · Law or regulation
Isolation and handbackabout 1 hour
Process isolation separates plant from hazardous energy and substances. Handback returns it to service only after checks that the work area and people are clear.
HSE's HSG253 gives guidance on isolating plant and equipment safely and on reducing the risk of releasing hazardous substances during intrusive activities such as maintenance and sampling. Handback is the reverse: before devices are removed and energy restored, OSHA's lockout standard says the work area must be inspected for nonessential items and the equipment checked as operationally intact, and employees must be safely positioned or removed. A verbal 'all clear' is not a check of the area. A handback walk with the maintainer and the operator is one way to do that check.
- The safe isolation of plant and equipment (HSG253) HSE (UK) · Guide The safe isolation of plant and equipment.
Contractor selection and inductionabout 1 hour
Choose contractors on competence, agree the scope and hazards, and give every worker a site-specific induction before work starts.
HSE's contractor guidance says safe working with contractors is a challenge and gives practical steps. Under the UK CDM Regulations a principal contractor must check that anyone appointed has the skills, knowledge, experience and where relevant the organisational capability for the work, and must ensure all workers have site-specific inductions. Before selection, ask for the contractor's own risk assessments and examples of past work, rather than choosing on price and checking nothing until the first incident.
- Managing contractors (HSG159) HSE (UK) · Guide
- CDM 2015: principal contractors HSE (UK) · Guide
Simultaneous operationsabout 1 hour
When two jobs share a place or an interface at the same time, each can be safe alone and dangerous together.
Typical clashes are hot work below a lifting operation or one crew opening a line while another tests it, which is why reviewing permits one at a time misses the combination. OSHA's multi-employer citation policy shows how regulators reason: an employer that creates a hazard exposing another employer's workers can be held responsible, and the policy defines creating, exposing, correcting and controlling employers. Practical controls are a permit board that shows all live permits in an area, one authority per area and a short coordination meeting before each shift.
- Multi-employer citation policy (CPL 02-00-124) OSHA (US) · Guide
Permit auditsabout 1 hour
Audit permits at the work location: compare the paper to the precautions in place, and check closure and retained records.
A permit is only as good as the checks behind it, and auditing the filing cabinet while never visiting the work misses the point. OSHA's confined space standard shows what a permit contains: the space, purpose, authorised entrants, hazards, isolation measures, acceptable entry conditions, test results and rescue arrangements, and cancelled permits are kept for at least one year (as read on 20 November 2026). When auditing, pick live permits, go to the job and check that each listed precaution is physically there, then check closure and cancelled permits. HSG250 also covers audits and system reviews.
- 29 CFR 1910.146: permit-required confined spaces OSHA (US) · Law or regulation
Stop-work authorityabout 1 hour
Anyone should be able to stop unsafe work without blame. The law backs this in some regions and a company policy can extend it.
The EU directive (Article 8) requires employers to enable workers to stop work and move to safety in serious, imminent and unavoidable danger, and says they must not be disadvantaged for doing so. OSHA says US workers can raise safety concerns without being punished. Many sites write the same idea into a stop-work policy. Example: a rigger stops a lift because the exclusion zone is not clear and is thanked, and the lift resumes after the zone is secured. A stop-work policy that supervisors punish in practice protects nobody.
- Council Directive 89/391/EEC (framework directive) EUR-Lex · Law or regulation Article 8 covers serious and imminent danger.
- Worker rights OSHA (US) · Guide
Practice task
Design a one-page permit-to-work form and a one-page isolation and handback checklist for one high-risk job, such as hot work on a maintenance shutdown. Then audit three imaginary permits against it and write down what you would check at the work location.
Skills you build
Permit to workLockout and isolationContractor managementPermit auditingStop-work authority
Resources for this topic
Every source here is free. Each link opens the provider's own site in a new tab.
- Guidance on permit-to-work systems (HSG250) HSE (UK) · Guide Free to download; written for petroleum and chemical industries but widely used.
- Control of hazardous energy (lockout/tagout) OSHA (US) · Guide
- Confined spaces OSHA (US) · Guide
- Process safety management OSHA (US) · Guide Links to the PSM standard (29 CFR 1910.119), which covers hot work permits, contractors and pre-startup review for covered processes.
Jobs related to Environmental, health and safety (EHS) officer
No title matches the role itself right now, so these are live jobs in the same field.
Spot a problem with this topic?
Tell us what is wrong, missing or unclear here. Your note is attached to this topic.
Notes are sent from this page with JavaScript on. Without it, write to us on the contact page.